「天津硬质快速门」快速门安装教程具体步骤-北京快速门-北京龙盛快速门制造有限公司

广西11选5走势图

行业新闻
「天津硬质快速门」快速门安装教程具体步骤
时间: 2019-07-15 08:26 浏览次数:
在快速堆积门安装工作进行前,要将安装工具准备齐备,一般包括手动电钻、角磨机、电动扳手、电锤及常用手动工



「天津硬质快速门」快速门安装教程具体步骤

 

Specific steps for installation of Tianjin Hard Fast Gate



 

在快速堆积门安装工作进行前,要将安装工具准备齐备,一般包括手动电钻、角磨机、电动扳手、电锤及常用手动工具(可根据个人安装习惯及实际情况适当增减)。


Before installing the quick stacking door, the installation tools should be ready, including manual electric drill, angle mill, electric wrench, electric hammer and common manual tools (which can be increased or decreased according to personal installation habits and actual conditions).


安装第一步:在平坦地面上将所要安装堆积门的轨道及门罩部分平放,并预先摆正位置,进行前期测量、描点,并用手动电钻在预定位置钻眼儿,用螺丝将轨道和门罩固定在一起。


Installation step 1: Place the track and the door cover part of the stacking door on the flat ground, set the position in advance, carry out preliminary measurement and tracing, and use manual electric drill to pre-position the drill hole, fix the track and the door cover together with screw.


安装第二步:在轨道两侧边安装防尘防风毛刷,如应用传统方法,需用铆钉将毛刷底座与轨道边缘固定到一处;如应用塑钢底座及扣槽,便可直接将毛刷安装在扣槽中,简略便捷。


Installation Step 2: Install dust-proof and wind-proof brushes on both sides of the track. If traditional methods are used, rivets are needed to fix the base of the brush to the edge of the track. If plastic steel base and buckle groove are used, the brush can be directly installed in the buckle groove, which is simple and convenient.
 


快速门编码器
 


安装第三步:按照计划要求,为电机、限位器(编码器)接通电线,需要注意的是要明确区分220V和380V两种情况下电机的接线方法,以免电机发现短路情况。


Installation Step 3: According to the requirements of the plan, connect the wire for the motor and the limiter (encoder). It should be noted that the connection method of the motor under 220V and 380V conditions should be clearly distinguished, so as to avoid the motor finding short circuit.


安装第四步:将安全背带一段固定在轴筒上,要注意预留长度要足够,大体长度连结一致。


Installation Step 4: Fix a section of the safety belt on the axle barrel, pay attention to the reserved length should be enough, the general length of the connection is consistent.

 

天津快速门厂家



安装第五步:将快速门门罩和轨道整体竖立起来,摆正到合适位置,利用红外水平仪测量两侧轨道距离地面高度是否一致,如确定一致,可以进行接下来的固定工作。


Fifth step of installation: erect the door cover and track as a whole, put them in the right position, and use the infrared level to measure whether the track height on both sides is consistent with the ground. If the same is determined, the following fixed work can be carried out.


安装第六步:安装电机、限位器(编码器),在两侧轨道选择适当的相同高度,安装红外防砸系统。


Installation step 6: Install motor and limiter (encoder), choose the same height on both sides of the track, and install infrared anti-smash system.


安装第七步:用云石锯切割地感线圈,埋入地感线,「唐山快速门」快速门运行时剧烈抖动的原因?,或者应用微波雷达,与地感线起到相同作用。


Installation Step 7: Cut the ground inductance coil with a marble saw and bury the ground inductance wire. Why does the "Tangshan Express Gate" tremble violently when it runs? Or use microwave radar to play the same role as ground-sensing lines.


安装第八步:接通线路,利用电机传动将帘布提升至适当高度并进行固定,调节上下限位。


Installation Step 8: Connect the line, use motor drive to raise the cord to the appropriate height and fix, adjust the upper and lower limit.


安装第九步:将顶部门罩保护壳及电机外罩固定。


Installation Step 9: Fix the top cover protective case and motor cover.
 


天津快速卷帘门



安装第十步:清理安装现场,对产品进行调试,「北京快速卷帘门」生产快速门需要哪些设备?,确保车辆行人正常通行。
 

Step 10: Clean up the installation site and debug the products. What equipment does Beijing Fast Rolling Curtain Door need to produce the fast door? To ensure the normal passage of vehicles and pedestrians.


「天津硬质快速门」快速门安装教程具体步骤


Specific steps for installation of Tianjin Hard Fast Gate


 

Copyright © 北京龙盛门业有限公司 版权所有
全国服务电话:13940183063   售后服务:024-31081023
公司地址:北京市怀柔区宝山镇

百度地图 - 网站地图

客服
电话
服务电话:
13940183063
微信

微信公众号

广西11选5开奖记录 广西11选5遗漏 广西11选5 广西11选5遗漏 广西11选5走势图 广西11选5 广西11选5 广西11选5遗漏 广西11选5开奖结果 大家乐彩票